The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. Align 3Gx flybarless setup problem Electric Heli Talk. Registered User Without the 3Gx module in place, with servos connected directly to.

Author: Nik Baramar
Country: Saint Lucia
Language: English (Spanish)
Genre: Marketing
Published (Last): 27 January 2008
Pages: 280
PDF File Size: 16.74 Mb
ePub File Size: 13.59 Mb
ISBN: 626-7-30583-773-2
Downloads: 11083
Price: Free* [*Free Regsitration Required]
Uploader: Vudolmaran

Are you sure you don’t remove the bind plug after powering down? Faster servos are able to execute commands from the gyro at faster and higher precision.

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic. In mine the section on RFS connection middle of page only says, “Care should be taken to ensure proper zlign color to channel connection. This setup mode sets the elevator gyro direction. Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless 3gd initial setup must be performed again.

Align 3GX v setup – RC

This completes the flybarless portion of the setup process. For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode non-heading lockor qlign and hold the SET button for 2 seconds. Reset throttle curve and pitch curve to default Eventually there will also be smartphone apps allowing live adjustments to 3GX without powering down.


In order to be able to post messages on the HeliFreak forums, you must first register. Tail pitch adjustment First check how the rudder responds to Tx. Problem solved — the aign is wrong!!

With all channels stationary, move the transmitter aileron stick to the right and then back to center position. I built my T-Rex during the week, and got a receiver for it yesterday, but I’m now having a problem setting up the flybarless system. Press the SET button to enter E. User need to confirm if 3GX is mounted right side up or upside down. My HK 3GX setup. Lift up the helicopter by hand, and turn it to the left yaw. The throttle stick position where main pitch is 0 degree must be maintained.

3GX Flybarless System – Introduction – Align

Page 1 of 2. Align 3Gx flybarless setup problem. The dramatically improved performance will create immediate impact on any enthusiasts. It is the instructions. Spektrum does make satellites but I am pretty sure they are not in any way compatible. REV begin to flash in sequence.

I wonder if US or other versions of the manual have the same incorrect illustration. In addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter. The trim must be zero when using 3GX, and should not be adjusted at anytime. Se “Trottle Calibration” at the end. Introduction Brand new redesigned 3GX represents a new generation of multi function flybarless system. Note that passwords are case-sensitive. LIM setup While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter Manjal.

Jul 06, He was getting a bit defensive, suggesting I had some kind of mix in my transmitter, but I kept reminding him it behaved normally when connected direct to my receiver. Actual gain value differs amongst manua and helicopters. Fail safes set wrong can cause your helli to spool up if there is a loss of connectivity with the TX.


Anti-torque Mwnual achieve consistent gyro gain on left and right, 3GX has built in anti-torque compensation function.

Anyway, after talking a while, with the manual in front of me, it dawned on me that there’s an error in the manual; on page 21 it shows the 3Gx connection to a Futaba RFS receiver, which is what mine is, as being red, orange, yellow, green, blue, purple in that order, from mxnual 1 to 6. Custom parameters have been opened up in 3GX to allow pilots to fine tune numerous settings for swashplate and rudder.

Align 3gx pdf manual

Cool, I appreciate the help! Should there be changes such as 3GX software update, pitch reconfiguration, or subtrim adjustments, the setup process must be repeated for the flybarless system.

With 3GX in operation mode, push rudder to left or right, and press the SET button manul about a second. Each heli and setup is different. Tilt the helicopter right as shown in diagramand check if swashplate is tilting correctly toward the left. This completes the rudder endpoint limit adjustment for the left side. Yep, the sats will blink fast whan you power the 3GX, they’ll go out for a few seconds while binding and come back on solid.

Author: admin